Make this part
Description
A Ø6.0 mm CNC-turned brass male bullet contact that clamps a stripped PV conductor in its rear bore with a radial cone-point grub screw — M3 in the 6 mm² build, M2.5 in the 4 mm² build. It exists because every off-the-shelf Ø6 mm bullet fails at least one of three things: 5.0 mm RC bullets sit too loose in a Ø6.0 mm female socket, RC battery-post bullets take the wire at 90° through the side so the cable cannot load inline, and pre-wired EC5 pigtails are unsafe to strip. It is dimensioned for the NIU FX Pro charge port, measured off the OEM charger plug in 2026-10 — Ø6.0 mm pins on a 15 mm pitch with 17.0 mm of pin proud of the housing collar. v4 is a bar-stock part: one Ø6.00 diameter for the whole 27 mm, a flat nose with a 0.80 × 45° edge break instead of a dome, and two shallow opposed locking flats in the solid mid-zone that clock the pin and stop it turning.
Specifications
| Role | contact-pin |
|---|---|
| Build | cnc-machined |
| Contact Diameter Mm | 6 |
| Pin Protrusion Mm | 17 |
| Overall Length Mm | 27 |
| Body Diameter Mm | 6 |
| Wire mm² | 6 |
| Wire Bore Mm | 3.55 |
| Set Screw | M3 × 4 mm cone point (DIN 914 / ISO 4027) |
| Set Screw Tap Drill Mm | 2.5 |
| Material | H59 brass (or T2 copper) |
| Finish | as-machined Ra 1.6 — conductive, never anodised or painted |
| Pitch Mm | 15 |
| Locking Flats | 2 opposed, 1.40 × 0.40 mm, 5.20 mm across flats (x = −0.60..+0.80) |
| Nose | flat, 0.80 × 45° edge break (tip face Ø4.40) |
What else you need
This download is the CAD only. The set screw is the part that decides whether the joint holds, and the housing is what keeps two live pins apart.
Machining notes
| Process | CNC turning — no 5-axis work, no printed part |
|---|---|
| Material | H59 brass (C36000 free-machining is fine); T2 copper also works |
| Finish | As-machined Ra 1.6 — never anodised, painted or powder-coated |
| Pin tolerance | Ø6.00 +0.00/−0.03 mm over the full 17 mm protrusion |
| General tolerance | ±0.05 mm (ISO 2768-m) |
| Thread | M3 × 0.5 - 6H (6 mm²) / M2.5 × 0.45 - 6H (4 mm²) — callout only |
| Quantity | 2 per vehicle, one per charge pin |
Assembly
1. Send the STEP and the drawing — nothing else
The STEP is the solid with a plain tap drill, on purpose: a modelled thread only gives CAM a helical surface to chase. The drawing carries the M3 × 0.5 - 6H callout and the Ø6.00 tolerance, and that is what produces the thread.
2. Check the first pair against your own port
The geometry is measured from the OEM charger plug; the fit is not proven. Check the pin diameter and the 17 mm protrusion on the first pair before ordering a batch, and check that the 0.80 × 45° nose break enters the socket without a burr catching on the crown spring.
3. Strip, insert, and tighten the set screw
Strip 6 mm of insulation and do not tin the strands — a set screw grips bare copper. Push the conductor fully into the rear bore until it bottoms, run the set screw in (M3 for the 6 mm² build, M2.5 for the 4 mm² build), and tug-test it.
4. Meter polarity before anything is connected
Read polarity from the isolated OEM charger plug, never from the bike. Mark + and − on the housing, then check for continuity between the two pins before the first connection.
Parts you’ll need
The set screw and its hex key are the only things the pin itself needs — and the wire gauge picks which screw. The housing is the part that turns two bare contacts into a connector.