Clamps stripped 4 mm² solar PV cable directly inside two Ø6.0 mm RCPROPLUS Supra X S6 (`REB6808STS6`) solderless set-screw bullets with an M3 × 4 mm grub screw (1.5 mm hex key). Fold the stripped 4 mm² copper strands over once before tightening so the screw has full purchase in the 8–10 AWG bore. Print `housing-bottom.stl` + `housing-top.stl`.
Make this part
Description
Designed to fit inside the NIU FX Pro's proprietary female charge port — the port no one else makes an adapter for. The only alternative is to buy a complete replacement NIU charger and harvest its connector, which costs around US$240. Version 5 mates with the ScootSolar CNC-turned Ø6.0 mm set-screw contact (`cnc-set-screw-bullet-6mm`): the pocket is Ø6.15 mm and carries two opposed locking pads that drop into that contact's wrench flats, which clocks the pin, stops it turning under the hex key, and holds it axially in both directions at the 17 mm of pin the OEM charger plug has. The contact clamps your stripped 4 mm² or 6 mm² PV cable directly inside the housing with a 1.5 mm hex key — no soldering, no crimping, and no cutting plastic housings off pre-wired pigtails.
Specifications
| Connector Family | niu-proprietary |
|---|---|
| Charge Voltage V | 82.77 |
| Contact Diameter Mm | 6 |
| Build | 3d-printable-cad |
| Wire mm² | 4 |
Connections
| in | screw-terminal · ≤90 V |
|---|---|
| out | niu-proprietary · ≤87.6 V |
What you still need to source
The download is the plastic only. These are the rest, and the contact is the one that decides whether it works.
Print settings
| Orientation | Split face DOWN, both halves |
|---|---|
| Supports | None — the channels print open |
| Layer height | 0.2 mm (0.12 mm on the split face if the channels feel rough) |
| Walls | 3–4 — the shroud plates are only 2 mm thick, so the walls are the part |
| Infill | 15–20 %, gyroid or grid |
| Material | ASA outdoors, PETG indoors. Never PLA |
Assembly
1. Print the two halves for your solar cable gauge
Print `housing-bottom.stl` + `housing-top.stl` for 4 mm² PV cable (Ø6.3 mm ribbed bore), or `housing-bottom-6mm.stl` + `housing-top-6mm.stl` for 6 mm² PV cable (Ø7.4 mm ribbed bore). Print both halves split-face down with no supports.
Print the two halves separately. Do not print them as one piece.
2. Strip the PV cable and clamp the Ø6.0 mm contacts
Strip 6 mm of insulation off the end of each vehicle-side PV lead and do not tin the strands — a set screw grips bare copper. Push the conductor into the rear bore of each contact until it bottoms.
Tighten the set screw firmly with the matching hex key (M3 × 4 mm / 1.5 mm for the 6 mm² build, M2.5 × 4 mm / 1.3 mm for the 4 mm² one). Tug-test both leads before loading them into the housing.
3. Drop the contacts in flats-down, set screws pointing DOWN
Each half of the housing carries one locking pad inside the pocket. Drop each contact into the BOTTOM shell with its two opposed flats sitting on that pad and the protruding set screw pointing straight DOWN into the radial relief cavity.
The flats are what clock the contact: if it will not drop in, it is 90° out — turn it and it seats. The flats' rear shoulder lands on the pad's rear face, which is what fixes the pin protrusion at 17 mm past the collar face.
4. Close the shells
The Ø4 × 25 mm alignment rib at the centre of the split face drops into the groove in the top half, and the top shell's own pad comes down onto the opposite flat. Line the two halves up roughly and they cam into register as they close.
Drive the two M2.6 × 14 mm (or M2.5 × 14 mm) self-tapping pan-head screws in until snug — do not over-torque. The shells locate the contact; the screws only hold the shells together.
5. Check polarity before it goes near the scooter
The port's polarity is not recorded, and the housing's keying is the first guard, never the only one. Learn it from the OEM charger's plug rather than from the scooter's socket. Both can be metered — but the charger's output is isolated, it keys into the socket the same way the adapter does, and it is the known-good mating part. The socket is a live pack terminal with two contacts 15 mm apart down a recess, so the risk there is not the voltage but a slipped probe bridging + and −; if you do measure it, put the meter on DC volts first, because a current range turns that slip into a dead short. Mark + and − on the shell once you know.
Then meter for continuity between the two bullets before the first connection. A reversed connection into a battery pack is the one mistake in this build that destroys hardware.
Parts you’ll need
Please purchase the remaining off-the-shelf parts here to complete the adapter.