Every part you need to charge the Pacific Nimbuzz from solar panels: a 200W kit sized for 30 km a day, with current Indonesia prices.
~Rp 4,786,310
Priced items only · vehicle not included
Some lines are converted from USD at the regional estimate — each row shows the price its shop charges.
Estimated payback: about 2.6 years
Roughly Rp 1,872,450 a year you no longer spend on petrol — about 187 L, the petrol a 50cc moped would burn over your 30 km a day at today's local price.
Rp 9,362,250
Petrol avoided in 5 years
Rp 18,724,500
Petrol avoided in 10 years
Disclaimers — please read
Some links here are affiliate links. If you buy through them we may earn a commission, at no extra cost to you — it never changes the price you pay, or which parts we recommend. The kit is sized from your vehicle, your daily distance and your local sun. As an Amazon Associate we earn from qualifying purchases.
Jinyang PV-BX200 folding 200 W panel
Sized from your daily distance and local sun hours. The single biggest line item.
Buy on Lazada4 mm² PV cable pair, 5 m, MC4 to bare
Gauge is computed from your current and run length, not assumed. This run loses 0.4% of the voltage (99.6% arrives). Buy 6mm² to reduce the loss to 0.3%.
Buy on badank ElectronicJNGE MPPT boost charge controller
Must accept at least 200W of PV, tolerate the panel's open-circuit voltage, and be settable to your pack's charge voltage. Keep it clean, dry, and in the shade (try under your house).
Buy on LazadaScootSolar MPT-7210A Outdoor Safety Shell — 6 mm² in / 6 mm² out (3D-Printable CAD)
Your kit uses 6 mm² cable from the panel and 6 mm² cable to the vehicle, so print the 6 mm² in / 6 mm² out variant. Replaces the bulky junction box when your controller sits under an eave or roof: clamps all 4 solar and battery cables in half-round ribbed channels so a trip yank cannot pull bare wires out of the screw terminals, and locks the voltage buttons + screw holes behind a tamper-proof shield while leaving the LCD and cooling fan 100% open.
6 mm² PV1-F solar cable, per metre
Gauge is computed from your current and run length, not assumed.
Buy on LazadaCASTA Heat-shrink solder-seal splice kit, 50 pcs with case
The charge adapter's lead is only 0.45 m and your run is 3 m, so the two cables have to be joined inside the body. Both ends are thick wire — the adapter's two thickest leads are 10 AWG (about 5 mm²) and the cable is 4 mm² — so use one of the yellow 4.0–6.0 mm² splices in this box. Strip 13 mm of insulation off each end, SLIDE THE TUBE ON FIRST — you cannot get it over the join afterwards — push both ends in until they meet at the solder ring in the middle, then heat it with a heat gun until the ring melts and the tube shrinks onto the insulation. No crimping tool and no soldering iron needed, and the glue inside seals both ends. Pull on it before it cools: a bad join looks exactly like a good one.
Buy on LazadaH&L PRO 1500 W hot air gun
Melts the solder ring in a solder-seal splice, and shrinks adhesive-lined heat-shrink over a joint. A 300 W mini gun reaches about 250 °C, which is enough with patience; this 1500 W one is rated 300–520 °C and is the right tool for a join you only want to make once. Never use a lighter: the heat is uneven, the insulation scorches, and the join looks sealed when it is not.
Buy on Lazada3-pin trapezium (品字 / T-type) male plug pigtail, 45 cm lead — 品字公头
Arrives as a plug on its own lead, ending in bare conductors. Terminate it at the bench BEFORE the plug goes near the scooter — its charge port is a live battery terminal, so two loose ends touching is a dead short across the pack. Take the polarity from the OEM charger's plug (an isolated DC output, safe to meter), not from the bike; heat-shrink each conductor, insulate the pins you do not use, and meter for continuity between + and − before the first connection.
Buy on AmazonMultifunctional wire stripper and cutter, 10–20 AWG
Every join in the guide starts with "strip 13 mm", and the cable is cut to length first. Most MC4 crimping kits do not include a pair. Its stripping holes stop at 10 AWG (2.6 mm); a 6 mm² conductor is thicker, so strip that end by scoring the insulation with the cutter blade and pulling it off.
Buy on LazadaXL830L digital multimeter
Check polarity and voltage before you connect anything. Continuity, DC volts and a buzzer — nothing a kit this size needs more of.
Buy on LazadaInsulated knit work gloves, 400 V (pair)
For the charge port and the battery terminals, where a slip should not mean skin on metal. The 400 V on the listing is the seller's claim on a coated knit glove, not an IEC 60903 test — sensible insurance on an 84 V pack, not a license to work on live conductors.
Buy on LazadaSafety glasses, clear lens
Buy the clear lens — the same listing also sells a dark one, which is a sunglass lens and no use in a shed. A step bit throws plastic swarf and a cutter throws copper strands, and both go where you are looking.
Buy on LazadaScootSolar Solar Kit Assembly Instructions + AI Build Assistant
A step-by-step guide, ours not a retailer's: panel placement, wiring the controller terminals, configuring the MPPT, and verifying polarity and charge voltage with a multimeter. Available on Mobile Web or Desktop. Includes US$5 of AI credits for an AI build assistant. You can send it photos and ask for help at any step. Charged in USD by Lemon Squeezy, so it is shown separately from the parts total.
Untick anything you already own.
MG Junction box 380 × 300 × 120 mm, IP55 (MG 01 12 01)
For an install that gets rained on. A cold, dry, shaded spot is enough on its own — the controller only needs to stay out of the sun and off the ground. Even a cheap box with rubber grommets is fine: it's a rain shelter, not a sealed enclosure, and 4mm² cable is stiff enough that many people leave the lid off. Sealing it takes three more things, and the box alone is useless without them: the glands below (two, one per cable), a drill, and a step bit — a twist bit wanders and leaves an oval no gland can seal. If you have no drill, buy a pre-drilled enclosure instead.
Buy on LazadaCable glands, locknuts and O-ring washers
One per cable entry, so two for this kit. Only needed if you seal the box — an open hole is a box that fills with water. 4mm² cable is stiff, so many people leave the lid off instead. Buy them as a set — a gland with no locknut cannot be fixed to the wall, and without its rubber O-ring washer it leaks at the hole.
Find on LazadaStep drill bit
The one tool that decides whether the box seals. A step bit cuts a round, burr-free hole through plastic or thin steel in one pass, and its steps cover every gland size. A twist bit wanders and leaves an oval — a gland cannot seal an oval.
Find on LazadaPower drill
Most people already own one. Any corded or cordless drill will drive a step bit; slow speed and light pressure is what stops the plastic melting and the hole going out of round.
Find on LazadaDeburring tool or fine sandpaper
Takes the burr off the inside of the hole. A gland's rubber washer seals against a flat face — a raised burr holds it off, and the box leaks exactly where the cable enters.
Find on LazadaWrench or spanner (gland size)
For the gland's locknut. Match it to the gland — PG9 and M20 take different spanners — and take the across-flats figure from the gland's own listing rather than guessing.
Find on LazadaCable lock / security tether
Theft is the real risk when panels live outside. Recommended if they're not fenced.
Find on LazadaCable ties and routing clips
Cheap, and the thing everyone forgets. The sourced pack is 100 cable ties; add routing clips separately if the run needs them.
Find on LazadaPanel mount or ground stand
Not needed if the panel lies on the ground in a fenced spot. Worth it for an angle or a windy site.
Find on LazadaTrenching shovel (bury the PV cable)
A 4 in narrow blade and a long handle: it cuts a slot rather than a hole, so a 150 mm trench for the panel cable costs you ten minutes and a strip of lawn. Burying is what keeps the lead out of a mower, a dog's teeth and a child's path — and it is the same shovel for the run to the controller.
Find on LazadaMC4 crimping tool, 2.5–6 mm²
Crimps the MC4 connectors. Many kits don't include cutters or strippers — check yours before you skip the next line.
Buy on badank ElectronicHeat-shrink sleeve for the joint
For a Western Union splice, or to add a second seal over a splice that did not shrink onto the insulation. Slide it on BEFORE you twist or solder — you cannot get a tube over a finished joint. 20 mm expanded fits over the splice and shrinks onto both cable jackets; two per kit, one per polarity.
Find on LazadaSolar lights (garden or security)
A popular add-on — the panel and sun hours you already have will run them too.
Find on LazadaMC4 inline DC fuse, 1000 V / 30 A (2 pcs)
Belt and braces: the controller limits its output and the scooter has its own fuse, so this is not required. Fit one if the vehicle-side run is long, or if you want a fuse you can see and reach. If you do, put it on the vehicle side, close to the scooter — that is the run a fault in the plug would short. The MC4 inline fuse listed suits the panel side; the vehicle side needs a blade-fuse holder on the same gauge.
Buy on badank ElectronicKeep this list
Print it now, or save it as a PDF, if you want a copy of the list to take with you.
The first five years