Every part you need to charge the Ride1Up Revv1 DRT from solar panels: a 200W kit sized for 51 km a day, with current USA prices.
~$451.11
Priced items only · vehicle not included
Estimated payback: about 1.3 years
Roughly $359 a year you no longer spend on gas — about 318 L, the gas a 50cc moped would burn over your 51 km a day at today's local price.
$1,795
Gas avoided in 5 years
$3,591
Gas avoided in 10 years
Disclaimers — please read
Some links here are affiliate links. If you buy through them we may earn a commission, at no extra cost to you — it never changes the price you pay, or which parts we recommend. The kit is sized from your vehicle, your daily distance and your local sun. As an Amazon Associate we earn from qualifying purchases.
ALLPOWERS SP027 100 W folding panel
2 × 100W panels wired 2S — 36V at 6.0A. Series raises the voltage and lowers the current, so the cable can be thinner.
Buy on AmazonWindyNation 10 AWG PV cable pair, 20 ft red + 20 ft black, UL 4703
Gauge is computed from your current and run length, not assumed. This run loses 0.5% of the voltage (99.5% arrives).
Buy on AmazonCallsun DY-MLUE-500W 15 A boost MPPT
Must accept at least 200W of PV, tolerate the panel's open-circuit voltage, and be settable to 58.8V. Keep it clean, dry, and in the shade (try under your house).
Buy on AmazonWindyNation 10 AWG PV cable pair, 20 ft red + 20 ft black, UL 4703
Gauge is computed from your current and run length, not assumed. This pair arrives with an MC4 on each end: the controller end is cut off and stripped, because a screw terminal takes bare wire. This run loses 0.1% of the voltage (99.9% arrives).
Buy on AmazonCharge adapter — Ride1Up Revv1 DRT
3D printed to order from the CAD files — print it yourself, or hand the files to a print shop. Strip your wire, push it into the Ø6 mm set-screw bullet and tighten the set screw in its side to bind the strands — no crimp tool or soldering iron. The two housing halves screw together around the bullets so they cannot short, and the connector is keyed so it only fits one way — never upside down.
KAIWEETS Self-adjusting wire stripper, 10–24 AWG, strip / crimp / cut
Every join in the guide starts with "strip 13 mm", and the cable is cut to length first. Most MC4 crimping kits do not include a pair. Its stripping holes stop at 10 AWG (2.6 mm); a 6 mm² conductor is thicker, so strip that end by scoring the insulation with the cutter blade and pulling it off.
Buy on AmazonAstroAI AM33D digital multimeter, 2000 counts
Check polarity and voltage before you connect anything. Continuity, DC volts and a buzzer — nothing a kit this size needs more of.
Buy on AmazonMAGID M0011R11 Class 00 rubber insulating gloves, size 11
For the charge port and the battery terminals, where a slip should not mean skin on metal. The 400 V on the listing is the seller's claim on a coated knit glove, not an IEC 60903 test — sensible insurance on an 84 V pack, not a license to work on live conductors.
Buy on AmazonNoCry Clear safety glasses, anti-fog, wrap-around, ANSI Z87
Buy the clear lens — the same listing also sells a dark one, which is a sunglass lens and no use in a shed. A step bit throws plastic swarf and a cutter throws copper strands, and both go where you are looking.
Buy on AmazonScootSolar Solar Kit Assembly Instructions + AI Build Assistant
A step-by-step guide, ours not a retailer's: panel placement, wiring the controller terminals, configuring the MPPT, and verifying polarity and charge voltage with a multimeter. Available on Mobile Web or Desktop. Includes US$5 of AI credits for an AI build assistant. You can send it photos and ask for help at any step. Charged in USD by Lemon Squeezy, so it is shown separately from the parts total.
Untick anything you already own.
Weatherproof box for the controller
For an install that gets rained on. A cold, dry, shaded spot is enough on its own — the controller only needs to stay out of the sun and off the ground. Even a cheap box with rubber grommets is fine: it's a rain shelter, not a sealed enclosure, and 4mm² cable is stiff enough that many people leave the lid off. Sealing it takes three more things, and the box alone is useless without them: the glands below (two, one per cable), a drill, and a step bit — a twist bit wanders and leaves an oval no gland can seal. If you have no drill, buy a pre-drilled enclosure instead.
Find on AmazonCable glands, locknuts and O-ring washers
One per cable entry, so two for this kit. Only needed if you seal the box — an open hole is a box that fills with water. 4mm² cable is stiff, so many people leave the lid off instead. Buy them as a set — a gland with no locknut cannot be fixed to the wall, and without its rubber O-ring washer it leaks at the hole.
Find on AmazonStep drill bit
The one tool that decides whether the box seals. A step bit cuts a round, burr-free hole through plastic or thin steel in one pass, and its steps cover every gland size. A twist bit wanders and leaves an oval — a gland cannot seal an oval.
Find on AmazonPower drill
Most people already own one. Any corded or cordless drill will drive a step bit; slow speed and light pressure is what stops the plastic melting and the hole going out of round.
Find on AmazonDeburring tool or fine sandpaper
Takes the burr off the inside of the hole. A gland's rubber washer seals against a flat face — a raised burr holds it off, and the box leaks exactly where the cable enters.
Find on AmazonWrench or spanner (gland size)
For the gland's locknut. Match it to the gland — PG9 and M20 take different spanners — and take the across-flats figure from the gland's own listing rather than guessing.
Find on AmazonWARLION 6 ft x 3/8 in adjustable braided-steel cable lock, dual loop
Theft is the real risk when panels live outside. Recommended if they're not fenced.
Buy on AmazonGardner Bender 48-308UVB mounting cable ties, 8 in, 50 lb, UV black (100 pack)
Cheap, and the thing everyone forgets. The sourced pack is 100 cable ties; add routing clips separately if the run needs them.
Buy on AmazonECO-WORTHY Ground-mount adjustable panel brackets, 2 sets, 118 in rail, 28.5°–60°
Not needed if the panel lies on the ground in a fenced spot. Worth it for an angle or a windy site.
Buy on AmazonTruper Tru Pro California trenching shovel, 4 in blade, 47 in ash handle (TRS-4C / 33094)
A 4 in narrow blade and a long handle: it cuts a slot rather than a hole, so a 150 mm trench for the panel cable costs you ten minutes and a strip of lawn. Burying is what keeps the lead out of a mower, a dog's teeth and a child's path — and it is the same shovel for the run to the controller.
Buy on AmazonGazoe Solar PV crimping tool, 2.5 / 4.0 / 6.0 mm² (14–10 AWG), ratcheting
Crimps the MC4 connectors. Many kits don't include cutters or strippers — check yours before you skip the next line.
Buy on Amazon1.5 mm hex key
For the charge adapter's set screws. An M3 set screw's socket is smaller than an M3 cap screw's — 1.5 mm, not 2.5 mm.
Find on AmazonTuffenough Solar motion flood light, 2500 lm, 3 heads (2 pack)
A popular add-on — the panel and sun hours you already have will run them too.
Buy on AmazonInline DC fuse and holder
Belt and braces: the controller limits its output and the scooter has its own fuse, so this is not required. Fit one if the vehicle-side run is long, or if you want a fuse you can see and reach. If you do, put it on the vehicle side, close to the scooter — that is the run a fault in the plug would short. The MC4 inline fuse listed suits the panel side; the vehicle side needs a blade-fuse holder on the same gauge.
Find on AmazonKeep this list
Print it now, or save it as a PDF, if you want a copy of the list to take with you.
The first five years
How a Ride1Up Revv1 DRT charges from solar — and how far a kit takes it →