Solar Panel Kit for the

Every part you need to charge the TVS iQube 3.5 kWh from solar panels: a 300W kit sized for 35 km a day, with current India prices.

TVS iQube 3.5 kWh

300W Solar Kit for TVS iQube 3.5 kWh

Distance35 km/day

₹1,679

Priced items only · vehicle not included

Some lines are converted from USD at the regional estimate — each row shows the price its shop charges.

Estimated payback: about 0.1 years

Roughly ₹28,169 a year you no longer spend on petrol — about 268 L, the petrol a 125cc scooter would burn over your 35 km a day at today's local price.

₹140,844

Petrol avoided in 5 years

₹281,689

Petrol avoided in 10 years

Disclaimers — please read

  • This is sizing help, not an engineering approval or an electrical inspection. Installing or using a kit is your decision and your risk. The terms set out what we are and are not liable for.
  • Check the charge plug against your vehicle's socket before you order (gender, pin count and pin positions) — send us a photo if you are unsure.
  • Retailers set their own prices, stock and specs, and listings can change — verify each part that arrives against this list before use.

Your system

Solar Panels Array
100W+−100W+−100W+−
3 × 100W solar panels in series (3S)
Cables+−MC4barePanel cable — not sourced · 6 m red + 6 m black99.5% of the voltage arrives in either the sun or shade
Charge ControllerCharge controller — not sourcedSteps up voltage from 54V to 58.8V with 97.5% efficiency
Cables+−bare wirebareVehicle cable — not sourced · 4 m red + 4 m black99.7% of the voltage arrives in the sun, 99.8% in the shade
Charge adapterCharge adapter — not sourcedyou source the plug · wire it to the controller
Scooter Charge PortPORT+−tvsTVS iQube 3.5 kWh charge port
MC4 maleMC4 femalemated pairscrew terminalbare wireXT60i solar input

Some links here are affiliate links. If you buy through them we may earn a commission, at no extra cost to you — it never changes the price you pay, or which parts we recommend. The kit is sized from your vehicle, your daily distance and your local sun.

Core kit

300W solar array — 3 × 100W

3 × 100W panels wired 3S — 54V at 5.5A. Series raises the voltage and lowers the current, so the cable can be thinner.

Not yet sourced
3 panelsView price

DC cable, panel to controller — 4mm²

Gauge is computed from your current and run length, not assumed. This run loses 0.5% of the voltage (99.5% arrives). Buy 6mm² to reduce the loss to 0.3%.

Not yet sourced
5 m red + 5 m blackView price

MPPT charge controller

Must accept at least 300W of PV, tolerate the panel's open-circuit voltage, and be settable to 58.8V. Keep it clean, dry, and in the shade (try under your house).

Not yet sourced

DC cable, controller to vehicle — 4mm²

Gauge is computed from your current and run length, not assumed. This run loses 0.3% of the voltage (99.7% arrives).

Not yet sourced
4 m red + 4 m blackView price

Charge adapter — TVS iQube 3.5 kWh

This scooter's port is a connector we have identified, but nobody has measured it, so we will not name a part for it yet — you source the plug. A caliper across the plug's locking ring and a meter on the OEM charger's contacts settle both.

Not yet sourced

Wire cutters and strippers

Every join in the guide starts with "strip 13 mm", and the cable is cut to length first. Most MC4 crimping kits do not include a pair.

Not yet sourced

Multimeter

Check polarity and voltage before you connect anything. Continuity, DC volts and a buzzer — nothing a kit this size needs more of.

Not yet sourced

Insulated gloves

For the charge port and the battery terminals, where a slip should not mean skin on metal. The 400 V on the listing is the seller's claim on a coated knit glove, not an IEC 60903 test — sensible insurance on an 84 V pack, not a license to work on live conductors.

Not yet sourced

Safety glasses

Buy the clear lens — the same listing also sells a dark one, which is a sunglass lens and no use in a shed. A step bit throws plastic swarf and a cutter throws copper strands, and both go where you are looking.

Not yet sourced

MC4-compatible connector pairs

Crimp one pair onto each of the panel's bare leads so they mate with the panel cable's MC4 ends.

Not yet sourced
2 packsView price

Instructions

ScootSolar Solar Kit Assembly Instructions + AI Build Assistant
Solar Kit Assembly Instructions + AI Build Assistant

ScootSolar Solar Kit Assembly Instructions + AI Build Assistant

A step-by-step guide, ours not a retailer's: panel placement, cutting and crimping MC4, wiring the controller terminals, configuring the MPPT, and verifying polarity and charge voltage with a multimeter. Available on Mobile Web or Desktop. Includes US$5 of AI credits for an AI build assistant. You can send it photos and ask for help at any step. Charged in USD by Lemon Squeezy, so it is shown separately from the parts total.

RecommendedPreview
₹1,679≈ converted from $19.99

Optional extras

Untick anything you already own.

Weatherproof box for the controller

For an install that gets rained on. A cold, dry, shaded spot is enough on its own — the controller only needs to stay out of the sun and off the ground. Even a cheap box with rubber grommets is fine: it's a rain shelter, not a sealed enclosure, and 4mm² cable is stiff enough that many people leave the lid off. Sealing it takes three more things, and the box alone is useless without them: the glands below (two, one per cable), a drill, and a step bit — a twist bit wanders and leaves an oval no gland can seal. If you have no drill, buy a pre-drilled enclosure instead.

Find on Amazon

Cable glands, locknuts and O-ring washers

One per cable entry, so two for this kit. Only needed if you seal the box — an open hole is a box that fills with water. 4mm² cable is stiff, so many people leave the lid off instead. Buy them as a set — a gland with no locknut cannot be fixed to the wall, and without its rubber O-ring washer it leaks at the hole.

Find on Amazon

Step drill bit

The one tool that decides whether the box seals. A step bit cuts a round, burr-free hole through plastic or thin steel in one pass, and its steps cover every gland size. A twist bit wanders and leaves an oval — a gland cannot seal an oval.

Find on Amazon

Power drill

Most people already own one. Any corded or cordless drill will drive a step bit; slow speed and light pressure is what stops the plastic melting and the hole going out of round.

Find on Amazon

Deburring tool or fine sandpaper

Takes the burr off the inside of the hole. A gland's rubber washer seals against a flat face — a raised burr holds it off, and the box leaks exactly where the cable enters.

Find on Amazon

Wrench or spanner (gland size)

For the gland's locknut. Match it to the gland — PG9 and M20 take different spanners — and take the across-flats figure from the gland's own listing rather than guessing.

Find on Amazon

Cable lock / security tether

Theft is the real risk when panels live outside. Recommended if they're not fenced.

Find on Amazon

Cable ties and routing clips

Cheap, and the thing everyone forgets. The sourced pack is 100 cable ties; add routing clips separately if the run needs them.

Find on Amazon

Panel mount or ground stand

Not needed if the panel lies on the ground in a fenced spot. Worth it for an angle or a windy site.

Find on Amazon

Trenching shovel (bury the PV cable)

A 4 in narrow blade and a long handle: it cuts a slot rather than a hole, so a 150 mm trench for the panel cable costs you ten minutes and a strip of lawn. Burying is what keeps the lead out of a mower, a dog's teeth and a child's path — and it is the same shovel for the run to the controller.

Find on Amazon

MC4 crimping tool

Crimps the MC4 connectors. Many kits don't include cutters or strippers — check yours before you skip the next line.

Find on Amazon

Solar lights (garden or security)

A popular add-on — the panel and sun hours you already have will run them too.

Find on Amazon

Inline DC fuse and holder

Belt and braces: the controller limits its output and the scooter has its own fuse, so this is not required. Fit one if the vehicle-side run is long, or if you want a fuse you can see and reach. If you do, put it on the vehicle side, close to the scooter — that is the run a fault in the plug would short. The MC4 inline fuse listed suits the panel side; the vehicle side needs a blade-fuse holder on the same gauge.

Find on Amazon

Keep this list

Print it now, or save it as a PDF, if you want a copy of the list to take with you.

The first five years

What five years of running a TVS iQube 3.5 kWh actually costs

Cheaper than what?

Cost of ownership, 5 years

35 km/day · vehicle + kit + fuel + upkeep
TVS iQube 3.5 kWh + this kitThis model
₹123,272 · ₹1.93/km
Suzuki e-Access
₹223,246 · ₹3.50/km
Honda Activa e:
₹149,435 · ₹2.34/km
Yamaha AEROX E
₹308,744 · ₹4.83/km
Honda Activa 6G 110cc (Gas)
₹320,284 · ₹5.01/km

How a TVS iQube 3.5 kWh charges from solar — and how far a kit takes it →

Not ready to buy yet?

Leave your email and we'll tell you when a cheaper panel or controller turns up for the TVS iQube 3.5 kWh, and when the build guide is ready. Occasional and relevant — and one click to leave.

We do not sell or share your address, and every email has an unsubscribe link.