NIU FX Pro charge adapter

Clamps stripped 6 mm² (10 AWG) solar PV cable directly inside two Ø6.0 mm RCPROPLUS Supra X S6 (`REB6808STS6`) solderless set-screw bullets with an M3 × 4 mm grub screw (1.5 mm hex key). Print `housing-bottom-6mm.stl` + `housing-top-6mm.stl` (sized with Ø7.4 mm ribbed cable bores for 6 mm² jacket).

Make this part

Description

Designed to fit inside the NIU FX Pro's proprietary female charge port — the port no one else makes an adapter for. The only alternative is to buy a complete replacement NIU charger and harvest its connector, which costs around US$240. Version 5 mates with the ScootSolar CNC-turned Ø6.0 mm set-screw contact (`cnc-set-screw-bullet-6mm`): the pocket is Ø6.15 mm and carries two opposed locking pads that drop into that contact's wrench flats, which clocks the pin, stops it turning under the hex key, and holds it axially in both directions at the 17 mm of pin the OEM charger plug has. The contact clamps your stripped 4 mm² or 6 mm² PV cable directly inside the housing with a 1.5 mm hex key — no soldering, no crimping, and no cutting plastic housings off pre-wired pigtails.

Specifications

Connector Familyniu-proprietary
Charge Voltage V82.77
Contact Diameter Mm6
Build3d-printable-cad
Wire mm²6

Connections

inscrew-terminal · ≤90 V
outniu-proprietary · ≤87.6 V

What you still need to source

The download is the plastic only. These are the rest, and the contact is the one that decides whether it works.

  • 2ScootSolar CNC set-screw bullet — Ø6.0 mm, machined (STEP + drawing)Buy at scootsolarFirst-hand fit testing on v1 proved 5 mm bullets sit too loose in the NIU FX Pro's female charge pin, and bench testing proved cutting the nylon shell off pre-wired EC5 pigtails is unsafe (too easy to clip the wire). This is the contact the v5 pocket is built around: one Ø6.00 diameter over its whole 27 mm, two opposed locking flats that the housing's pads grip, and 17 mm of pin past the collar — the same as the OEM charger plug. The wire gauge picks the build: 6 mm² takes the M3 set screw into a Ø3.55 bore, 4 mm² the M2.5 into a Ø2.75 one. It is sold separately as `cnc-set-screw-bullet-6mm` (STEP + A3 drawing) because it is a turning job, not a print.
  • 2M3 × 4 mm cone-point set screw (6 mm² build) or M2.5 × 4 mm (4 mm² build)Buy at hvhindustrialBuyer-supplied and picked by the wire gauge, not by preference: the screw has to pass through the wire bore to reach the conductor, so the 4 mm² build cannot take the M3. Cone point, DIN 914 / ISO 4027 — DIN 916 is the cup point, and marketplace titles get that wrong.
  • 11.5 mm metric hex key (M3 build) or 1.3 mm (M2.5 build)Buy at ktwTwo keys, not one. An M3 set screw uses a 1.5 mm hex socket across flats; the M2.5 uses 1.3 mm (ISO 4027 min 1.27, so a 1.27 mm / 0.050 in key is the same tool). A 1.5–10 mm set stops one size too big for the smaller screw.
  • 2M2.6 × 14 mm (or M2.5 × 14 mm) self-tapping screw, pan headBuy at LazadaSold by its forming diameter on Lazada Thailand. The 2.1 mm pilot and 2.75 mm clearance holes suit M2.5 or M2.6 × 14 mm unchanged.
  • 1The kit's vehicle-side DC cable (4 mm² or 6 mm²)Enters the rear of the housing directly and is gripped by the three printed strain-relief ribs.
  • —ASA or PETG filamentNot PLA. A charge port sits in the sun, and a PLA part left there is a predictable failure.

Print settings

OrientationSplit face DOWN, both halves
SupportsNone — the channels print open
Layer height0.2 mm (0.12 mm on the split face if the channels feel rough)
Walls3–4 — the shroud plates are only 2 mm thick, so the walls are the part
Infill15–20 %, gyroid or grid
MaterialASA outdoors, PETG indoors. Never PLA

Assembly

  1. 1. Print the two halves for your solar cable gauge

    Print `housing-bottom.stl` + `housing-top.stl` for 4 mm² PV cable (Ø6.3 mm ribbed bore), or `housing-bottom-6mm.stl` + `housing-top-6mm.stl` for 6 mm² PV cable (Ø7.4 mm ribbed bore). Print both halves split-face down with no supports.

    Print the two halves separately. Do not print them as one piece.

  2. 2. Strip the PV cable and clamp the Ø6.0 mm contacts

    Strip 6 mm of insulation off the end of each vehicle-side PV lead and do not tin the strands — a set screw grips bare copper. Push the conductor into the rear bore of each contact until it bottoms.

    Tighten the set screw firmly with the matching hex key (M3 × 4 mm / 1.5 mm for the 6 mm² build, M2.5 × 4 mm / 1.3 mm for the 4 mm² one). Tug-test both leads before loading them into the housing.

  3. 3. Drop the contacts in flats-down, set screws pointing DOWN

    Each half of the housing carries one locking pad inside the pocket. Drop each contact into the BOTTOM shell with its two opposed flats sitting on that pad and the protruding set screw pointing straight DOWN into the radial relief cavity.

    The flats are what clock the contact: if it will not drop in, it is 90° out — turn it and it seats. The flats' rear shoulder lands on the pad's rear face, which is what fixes the pin protrusion at 17 mm past the collar face.

  4. 4. Close the shells

    The Ø4 × 25 mm alignment rib at the centre of the split face drops into the groove in the top half, and the top shell's own pad comes down onto the opposite flat. Line the two halves up roughly and they cam into register as they close.

    Drive the two M2.6 × 14 mm (or M2.5 × 14 mm) self-tapping pan-head screws in until snug — do not over-torque. The shells locate the contact; the screws only hold the shells together.

  5. 5. Check polarity before it goes near the scooter

    The port's polarity is not recorded, and the housing's keying is the first guard, never the only one. Learn it from the OEM charger's plug rather than from the scooter's socket. Both can be metered — but the charger's output is isolated, it keys into the socket the same way the adapter does, and it is the known-good mating part. The socket is a live pack terminal with two contacts 15 mm apart down a recess, so the risk there is not the voltage but a slipped probe bridging + and −; if you do measure it, put the meter on DC volts first, because a current range turns that slip into a dead short. Mark + and − on the shell once you know.

    Then meter for continuity between the two bullets before the first connection. A reversed connection into a battery pack is the one mistake in this build that destroys hardware.

Parts you’ll need

Please purchase the remaining off-the-shelf parts here to complete the adapter.