Every part you need to charge the Felo FW03 from solar panels: a 800W kit sized for 35 km a day, with current Thailand prices.
฿5,589
Priced items only · vehicle not included
Some lines are converted from USD at the regional estimate — each row shows the price its shop charges.
Estimated payback: about 0.6 years
Roughly ฿9,658 a year you no longer spend on petrol — about 268 L, the petrol a 125cc scooter would burn over your 35 km a day at today's local price.
฿48,290
Petrol avoided in 5 years
฿96,579
Petrol avoided in 10 years
Disclaimers — please read
Some links here are affiliate links. If you buy through them we may earn a commission, at no extra cost to you — it never changes the price you pay, or which parts we recommend. The kit is sized from your vehicle, your daily distance and your local sun.
LS-F200M folding 200W (2 × 100W)
4 × 200W panels wired 2S2P — 40.4V at 21.2A. Series raises the voltage and lowers the current, so the cable can be thinner.
Find on LazadaTMDA 6 mm² solar PV cable (PV1-F), sold per metre
Gauge is computed from your current and run length, not assumed. This run loses 1.0% of the voltage (99.0% arrives).
Buy on LazadaMPPT charge controller
Must accept at least 800W of PV, tolerate the panel's open-circuit voltage, and be settable to 109.2V. Keep it clean, dry, and in the shade (try under your house).
Not yet sourcedTMDA 4 mm² solar PV cable (PV1-F), sold per metre
Gauge is computed from your current and run length, not assumed. This run loses 0.2% of the voltage (99.8% arrives).
Buy on LazadaCharge adapter — Felo FW03
We have not measured this scooter's charge port yet, so we will not name a part for it. Measure the port (or ask us to) and the adapter is usually a plug you can buy.
Not yet sourcedWire cutters and strippers
Every join in the guide starts with "strip 13 mm", and the cable is cut to length first. Most MC4 crimping kits do not include a pair.
Not yet sourcedUNI-T UT890C / UT890D+ digital multimeter, 6000 count, True RMS
Check polarity and voltage before you connect anything. Continuity, DC volts and a buzzer — nothing a kit this size needs more of.
Buy on LazadaInsulated gloves
For the charge port and the battery terminals, where a slip should not mean skin on metal. The 400 V on the listing is the seller's claim on a coated knit glove, not an IEC 60903 test — sensible insurance on an 84 V pack, not a license to work on live conductors.
Not yet sourcedSafety glasses
Buy the clear lens — the same listing also sells a dark one, which is a sunglass lens and no use in a shed. A step bit throws plastic swarf and a cutter throws copper strands, and both go where you are looking.
Not yet sourcedLINK MC4 connector pair CB-1002A, 2.5–6 mm², 1500 V
2 cut lengths of cable join the strings' own leads to the combiner — each one needs an MC4 on both ends, which is why this row is here at all. Crimp a pair onto the panel's bare leads too if yours arrive without connectors.
Buy on LazadaMC4 Y-branch connector pair
2 parallel strings have to be joined back to one cable — a Y-branch pair per extra string.
Buy on LazadaScootSolar Solar Kit Assembly Instructions + AI Build Assistant
A step-by-step guide, ours not a retailer's: panel placement, cutting and crimping MC4, wiring the controller terminals, configuring the MPPT, and verifying polarity and charge voltage with a multimeter. Available on Mobile Web or Desktop. Includes US$5 of AI credits for an AI build assistant. You can send it photos and ask for help at any step. Charged in USD by Lemon Squeezy, so it is shown separately from the parts total.
Untick anything you already own.
ScootSolar PV Cable Bend Guide — 45° Interlocking Segment, 6 mm² (3D-Printable CAD)
Your kit uses 4 mm² (Ø6.1 mm) and 6 mm² (Ø7.2 mm) cables — both STL variants are included in one download. Interlocking 45° segments snap together like a toy train track so stiff solar cables never kink around outdoor corners: 2 segments make a 90° corner, 4 make a 180° U-turn, and 6 make a compact Omega loop in tight spaces. Each joint's shared ring takes one ground anchor through its 6.4 mm ear, so a staked run stays where you laid it.
Nano Junction box NANO-206Y, 202 × 202 × 103 mm, IP65
For an install that gets rained on. A cold, dry, shaded spot is enough on its own — the controller only needs to stay out of the sun and off the ground. Even a cheap box with rubber grommets is fine: it's a rain shelter, not a sealed enclosure, and 4mm² cable is stiff enough that many people leave the lid off. Sealing it takes three more things, and the box alone is useless without them: the glands below (two, one per cable), a drill, and a step bit — a twist bit wanders and leaves an oval no gland can seal. If you have no drill, buy a pre-drilled enclosure instead.
Buy on LazadaCable glands, locknuts and O-ring washers
One per cable entry, so two for this kit. Only needed if you seal the box — an open hole is a box that fills with water. 4mm² cable is stiff, so many people leave the lid off instead. Buy them as a set — a gland with no locknut cannot be fixed to the wall, and without its rubber O-ring washer it leaks at the hole.
Find on LazadaStep drill bit
The one tool that decides whether the box seals. A step bit cuts a round, burr-free hole through plastic or thin steel in one pass, and its steps cover every gland size. A twist bit wanders and leaves an oval — a gland cannot seal an oval.
Find on LazadaPower drill
Most people already own one. Any corded or cordless drill will drive a step bit; slow speed and light pressure is what stops the plastic melting and the hole going out of round.
Find on LazadaDeburring tool or fine sandpaper
Takes the burr off the inside of the hole. A gland's rubber washer seals against a flat face — a raised burr holds it off, and the box leaks exactly where the cable enters.
Find on LazadaWrench or spanner (gland size)
For the gland's locknut. Match it to the gland — PG9 and M20 take different spanners — and take the across-flats figure from the gland's own listing rather than guessing.
Find on LazadaCable lock / security tether
Theft is the real risk when panels live outside. Recommended if they're not fenced.
Find on LazadaELEKTRA Cable ties, 6 in, 3.6 mm (100 pcs)
Cheap, and the thing everyone forgets. The sourced pack is 100 cable ties; add routing clips separately if the run needs them.
Buy on LazadaPanel mount or ground stand
Not needed if the panel lies on the ground in a fenced spot. Worth it for an angle or a windy site.
Find on LazadaTrenching shovel (bury the PV cable)
A 4 in narrow blade and a long handle: it cuts a slot rather than a hole, so a 150 mm trench for the panel cable costs you ten minutes and a strip of lawn. Burying is what keeps the lead out of a mower, a dog's teeth and a child's path — and it is the same shovel for the run to the controller.
Find on LazadaKONY VX-9CQK crimping tool with VK-2546 MC4 jaw (2.5–6 mm²)
Crimps the MC4 connectors. Many kits don't include cutters or strippers — check yours before you skip the next line.
Buy on LazadaSolar lights (garden or security)
A popular add-on — the panel and sun hours you already have will run them too.
Find on LazadaInline DC fuse and holder
Belt and braces: the controller limits its output and the scooter has its own fuse, so this is not required. Fit one if the vehicle-side run is long, or if you want a fuse you can see and reach. If you do, put it on the vehicle side, close to the scooter — that is the run a fault in the plug would short. The MC4 inline fuse listed suits the panel side; the vehicle side needs a blade-fuse holder on the same gauge.
Find on LazadaKeep this list
Print it now, or save it as a PDF, if you want a copy of the list to take with you.
The first five years
How a Felo FW03 charges from solar — and how far a kit takes it →