Felo FW03
- Battery
- 96 V · 58 Ah5,568 Wh · NMC
- Motor
- 6,000 W
- Top speed
- 90 km/h
- Range
- 120 km
- Consumption
- 46.4 Wh/kmestimated
Can You Solar Charge a Felo FW03?
No AC inverter needed · No $500 power station · Plugs into the Felo FW03 charge port port
A 480 W solar array (4 × 120 W in series) feeding a DC boost MPPT controller recovers a 35 km/day commute on the Felo FW03 in about 5.2 peak sun hours (5 sun hours/day market average). The FW03 uses a 96 V 5,568 Wh NMC pack (recorded OEM charger ceiling: 109.2 V DC, confidence: Medium, source — always read your own charger nameplate & verify with a multimeter) and charges through its Felo FW03 charge port.
480 W Solar Array
4 × 120 W (2S)
~5.2 hrs sun for 35 km
Daily 35 km commute recovery
~1.1 yr payoff vs. gas
Saves ~$268/yr
Similar vehicles & kit parts
Riders also viewed
- Felo M148 V · 1.0 kWh150 W kit · Felo M1 charge port
EV - NIU FX Pro76.8 V · 2.5 kWh200 W kit · NIU FX Pro charge port
EV - EVNIU NQi GT Sport60 V · 3.1 kWh250 W kit · NIU N-series charge port
- Part480W solar array — 4 × 120WKit part
- DC cable, panel to controller — 4mm² min · 6mm² suppliedKit part
Part - DC cable, controller to vehicle — 4mm²Kit part
Part
2 · Kit Cost, Payoff Period & Direct DC Efficiency
Should You Solar Charge Your Felo FW03?
Let's consider the important factors — upfront kit cost, payback against buying gas and wall electricity, total cost of ownership versus a new gas scooter, air and noise pollution, and local legal rules in Thailand — so you can decide for yourself.
How much does a solar kit for a Felo FW03 cost?
A complete direct-DC solar charging kit for the Felo FW03 costs $298 (including 4 × 120 W monocrystalline panels, a DC boost MPPT controller, sized solar cables, and the matched Felo FW03 charge port plug) — roughly one-third the cost of a portable power station setup.
Will You Save Money over Gas?
10-Year Cumulative Fuel Savings — Felo FW03
~1.1 yrs
Payoff breakeven vs. buying gas (~$268/yr)
~3.3 yrs
Payoff breakeven vs. wall outlet (~$87/yr)
+$2,923
Net profit vs. gas by Year 10 ($1,046 in grid kWh avoided)
Is a solar-charged Felo FW03 really cheaper than petrol?
Felo FW03 + Solar
6 kW · 5.57 kWh NMC · 90 km/h · 120 km range
$3,497/5 yrs

Honda Wave 110i (Gas)
110cc · 55.6 km/L · 92 km/h
$1,538/5 yrs
Why direct DC boost beats a portable power station
Solar Efficiency
Share of panel wattage that reaches the battery
Charges the Felo FW03's own 5,568 Wh pack directly without wasting 25–28% of your solar wattage in a DC→AC→DC inverter loop.
Zero home breaker stress (off-grid ready)
Draws 0 W from your home breaker vs. 450 W from the factory AC brick — preventing breaker trips and charging in unpowered sheds or carports.
Will Solar-Charging a Felo FW03 Reduce Air Pollution (CO₂ & PM2.5)?
In Thailand, the utility power grid averages 440 g CO₂/kWh (18% coal/fossil share). Charging your Felo FW03 directly from solar eliminates both tailpipe exhaust and power-plant smokestack emissions:
Carbon Emissions per Kilometer (g CO₂/km)
Breathable PM2.5 Air Particles (mg PM2.5/km)
Sources: EPPO Thailand & Ember Electricity Data (~440 gCO2/kWh natural-gas + lignite grid mix); EMEP/EEA Two-Wheeler Emission Inventory & IPCC AR6.
Will Driving a Solar-Charged Felo FW03 Reduce Noise Pollution?
Decibels (dBA) are logarithmic: every +10 dB sounds twice as loud to the human ear. The Felo FW03's brushless electric motor cuts city pass-by noise by 23 dBA (~80% quieter) compared to a 125cc gas scooter, and solar-charges at 0 dBA:
Is It Legal to Solar-Charge a Felo FW03 in Thailand?
Relevant authority: Energy Regulatory Commission (ERC), MEA & PEA
In Thailand, MEA/PEA parallel-connection permits and ERC notifications apply only when a solar inverter is tied into a building's 230V AC distribution board. A standalone, portable or shed-mounted low-voltage DC solar kit that charges an electric scooter directly is an off-grid DC appliance and requires no utility registration.
- No MEA/PEA Grid Connection: 100% isolated from the 230V AC utility meter.
- Low-Voltage DC (< 60 V): Safe low-voltage DC array and boost controller.
- Stock Charge Port: Connects via the scooter's standard external charge plug.
Ride more or less than 35 km/day? Adjust your daily distance, panel mounting, and cable runs for the Felo FW03:
Size Your FW03 Kit →2a · Head-to-head
How does it compare to popular EVs?
Bars are scaled to the highest value in this group. Cost per km = vehicle price + its solar kit + upkeep, over the same distance for every row (35 km/day for 5 or 10 years); a model with no solar kit pays for grid energy instead. Prices are this market's own figures, shown in your display currency.
Price
new vehicle price- Felo FW03This model
- $3,048
- NIU NQi GT Sport
- $3,608
- NIU FX Pro
- $1,639
- Felo M1
- $1,639
Top Speed
- Felo FW03This model
- 90 km/h
- NIU NQi GT Sport
- 80 km/h
- NIU FX Pro
- 80 km/h
- Felo M1
- 45 km/h
Range
- Felo FW03This model
- 120 km
- NIU NQi GT Sport
- 85 km
- NIU FX Pro
- 80 km
- Felo M1
- 45 km
Battery Size
- Felo FW03This model
- 5.6 kWh
- NIU NQi GT Sport
- 3.1 kWh
- NIU FX Pro
- 2.5 kWh
- Felo M1
- 1.0 kWh
Motor Wattage
- Felo FW03This model
- 6 kW
- NIU NQi GT Sport
- 4.6 kW
- NIU FX Pro
- 2 kW
- Felo M1
- 700 W
Solar Chargeable
— = no plug on record yet- DC charging
- AC charging
- Felo FW03This model
- DC charging: not recorded
- AC charging: Yes
- NIU NQi GT Sport
- DC charging: Yes
- AC charging: Yes
- NIU FX Pro
- DC charging: Yes
- AC charging: Yes
- Felo M1
- DC charging: not recorded
- AC charging: Yes
Cost per km (5 years)
incl. vehicle + kit + upkeep- Felo FW03This model
- $0.05/km
- NIU NQi GT Sport
- $0.06/km
- NIU FX Pro
- $0.03/km
- Felo M1
- $0.03/km
Cost per km (10 years)
incl. vehicle + kit + upkeep- Felo FW03This model
- $0.03/km
- NIU NQi GT Sport
- $0.03/km
- NIU FX Pro
- $0.02/km
- Felo M1
- $0.02/km
Compare them side by side, attribute by attribute →
3 · Solar Kit Parts for Felo FW03
What do you need to solar charge a Felo FW03?
Click any part below to open the full parts list with safety disclaimers & live retailer links, or customize your daily distance and cable lengths in the free kit configurator:
8 m
8 m
4×
1×
Optional
Optional
OptionalEstimated core kit total: $298
See per-item pricing, electrical safety disclaimers, and direct local retailer links on the full parts list page.
Watch: 3D Solar Kit Assembly & Safe Wiring Sequence in Action
Placing the panel in full sun, landing PV and battery leads into the dead MPPT terminals first, verifying CV target voltage on the lit LCD, and closing the strain-relief armor.
4 · Complete BOM, 16-Step Assembly Guide & Safe Verification
How to Charge a Felo FW03 With Free Solar Power
To charge a Felo FW03 directly from sunlight without an AC inverter or portable power station, a 480 W solar array (4 × 120 W wired in 2S series) feeds a DC-DC boost MPPT controller that steps the array's 36 V Vmp up to your 96 V pack through its Felo FW03 charge port. We built two products specifically for the Felo FW03 so you never have to guess a part, wire gauge, or assembly step:
Your Felo FW03 Parts List (BOM)
Itemizes every required component and safety tool for your FW03 kit (estimated core total $298) with direct retailer links — cleanly separated from optional extras so you never overbuy:
- Required Core Hardware (7 items): 4 × 120 W solar panels, DC boost MPPT controller, 6 mm² panel cable (5 m run), 4 mm² vehicle cable (3 m run), matched Felo FW03 charge port plug.
- Required Build & Safety Tools (4 items): Digital multimeter (to test panel Voc & meter your OEM charger), wire cutters/strippers, insulated gloves, and clear safety glasses.
- Optional Extras (Never Required — unticked by default): 3D-printable MPPT strain-relief & button-locking shell, 45° PV cable bend guides, and an optional inline DC fuse (belt-and-braces protection for long runs — not required because the MPPT controller already limits its own output current and the scooter has a main battery fuse).
Solar Kit Assembly Instructions + AI Build Assistant
Our interactive step-by-step build guide generated specifically for your Felo FW03 configuration — taking you from unpacking boxes to a verified solar charge in strict dead-wires-first order:
- Tailored to your exact kit parts: Custom schematic diagrams and exact strip/cut lengths for your 6 mm² (5 m) panel run, 4 mm² (3 m) vehicle run, and Felo FW03 charge port connector.
- Strict dead-wires-first electrical order: Every screw terminal and wire splice is completed while panels are covered/unplugged and the scooter is disconnected — you never handle a live conductor.
- Includes US$5 of AI Build Assistant credit: Snap a photo of your multimeter reading, MPPT terminal wiring, or solder-seal splice at any step for instant verification before plugging in (plus read-aloud audio on every step).
The 4 Build Phases: How Your Felo FW03 Solar Kit Goes Together
Because the charge socket on your Felo FW03 is a live battery terminal, our 16-step assembly guide sequences the build into four distinct phases so you never guess polarity or work on live wires:
Check your BOM, test panel Voc (~21.6 V) in sun & dry-fit the layout
Verify all required parts and safety tools against your Bill of Materials (BOM). Before mounting anything (while still inside the seller's return window), place each panel in full sun and measure open-circuit voltage (~21.6 V DC per panel) with your multimeter. Position the panels in unshaded sun and the boost MPPT in dry ventilated shade, then dry-fit both cable runs before cutting wire.
Wire the array & land both MPPT terminal blocks while completely dead
Join the 4 panels (2S) and check ~43.2 V string Voc with your meter, then leave the panel MC4 leads unclipped (or keep panels covered). Route the 6 mm² panel cable and 4 mm² vehicle cable, and screw both into the MPPT's PV+/PV− and BAT+/BAT− terminals in one sitting while zero voltage is present.
Meter your isolated OEM charger plug & bench-splice the Felo FW03 charge port lead
Never plug bare pigtail wires into the scooter or probe the live vehicle socket blind. Plug your factory AC wall charger into the wall and probe its isolated DC output plug with your multimeter to identify positive (+) and negative (−). At the bench with everything disconnected, slide on the yellow 4.0–6.0 mm² solder-seal tube first, heat-splice the two power conductors, tug-test, insulate unused signal pins separately, and meter for zero continuity between + and −. (An inline DC fuse is optional belt-and-braces protection for long runs, not a requirement, since the MPPT limits its own output and the scooter has a main fuse.)
Boot the MPPT on solar, set your verified CV & current limits, plug in & verify on the dash
Clip the solar array MC4 connectors together first (with the scooter still unplugged) so the MPPT display boots on solar power. Read the DC OUTPUT rating on your own OEM charger nameplate (confirmed by your multimeter) and set the MPPT's constant-voltage (CV) ceiling at or slightly below that figure — never above — along with the current limit. Plug into the Felo FW03, watch watts climb on the controller, and verify after 10 minutes that your scooter's dashboard battery % has risen.
All 16 Steps Generated for Your Felo FW03 Kit
- 1Gather required parts & tools against your Bill of Materials (BOM)Free Sample
- 2Test each panel's open-circuit voltage (~21.6 V Voc) in full sun before mounting
- 3Plan the layout (panels in full sun, boost MPPT in dry shade, dry-fit cable runs)
- 4Mount or place the 4 panels with a 0.5 m seasonal service loop
- 5Wire the 4 panels in 2S2P & verify ~43.2 V string Voc with your multimeter
- 6Run the 5 m (6 mm²) panel cable to the controller (leave array unplugged)
- 7Strip 6–7 mm & crimp MC4 connectors onto the panel-side cable ends
- 8Wire the panel cable into the MPPT PV+ and PV− screw terminals while dead
- 9Run the 3 m (4 mm²) vehicle DC cable from the MPPT to your parking spot
- 10Wire the vehicle cable into the MPPT BAT+ and BAT− terminals in the same dead sitting
- 11Meter polarity on your isolated OEM charger plug & assemble the Felo FW03 charge port adapter at the bench
- 12Clip the solar array MC4 leads together to wake the MPPT display (~43.2 V PV in, scooter still unplugged)
- 13Read DC OUTPUT on your OEM charger nameplate, verify with your meter & set the MPPT CV ceiling
- 14Set the MPPT charge current limit at or below your OEM rating (this array supplies ~4.4 A)
- 15Plug the verified Felo FW03 charge port connector into the Felo FW03 & watch the MPPT settle into charging
- 16Confirm climbing watts on the MPPT & verify the scooter's dashboard battery % rises after 10 minutes
Recorded Felo FW03 Charger Specs & Connector Family
The table below lists the battery architecture, recorded OEM wall charger specifications with their confidence level and source, and our connector verification status. We never recommend an MPPT voltage setpoint: always read the DC OUTPUT rating on your own OEM charger nameplate and verify it with a multimeter.
| Nominal Voltage | 96 V DC |
|---|---|
| Pack Capacity | 5,568 Wh (58 Ah) |
| Battery Chemistry | NMC (Fixed on-board pack) |
| Recorded OEM Charger Rating | 109.2 V DC max Medium |
| Connector Family | Felo FW03 charge port Unverified |
| Pin Count & Gender on Vehicle | Unmeasured · unknown (on vehicle) |
| Adapter Verification Status | Identified · Family confirmed |
Solar Kit Assembly Instructions + AI Build Assistant
Follow interactive wiring diagrams for your exact cable gauge and connector family, with an AI build assistant ready to verify photos at every step.
5 · Felo FW03 Solar Charging FAQ & Distance Sizing
Felo FW03 Solar Charging FAQ
How many watts of solar do I need to charge a Felo FW03?
For a 35 km/day (21.7 mi/day) commute (~1624 Wh/day), the Felo FW03 needs a 480 W solar array (4 × 120 W wired in series) feeding a DC boost MPPT controller. At 5 peak sun hours/day, 480 W recovers a 35 km ride in about 5.2 sun hours. For a 40 km/day (24.9 mi/day) commute (~1856 Wh/day), step up to a 600 W array.
How do I verify the OEM charger voltage and pin polarity on the Felo FW03?
Our dataset records the Felo FW03 OEM charger ceiling at 109.2 V DC (confidence: medium), but you should never copy a voltage figure blindly from the web. Read the "DC OUTPUT" rating printed on your own original OEM AC wall charger nameplate, then plug the OEM brick in and probe its isolated DC output plug with a digital multimeter to verify both the constant-voltage ceiling and which pin is positive (+) and negative (−) before wiring your Felo FW03 charge port lead (port status: identified).
Can I charge the Felo FW03 from solar while riding?
No. Direct DC solar kits are designed for stationary daytime charging while parked at home or work, with the panels in full sun and the boost MPPT resting in ventilated shade. Many vehicle BMS units also inhibit throttle output while the charge port is active.
Sunshine Hours & Array Sizing by Daily Distance (10–40 km/day)
Computed from a consumption rate of 46.4 Wh/km, a 5,568 Wh pack, 5 peak sun hours/day in Thailand, a 0.70 real-world panel derating factor, and boost MPPT + DC cable efficiency.
| Daily Distance | Daily Wh | Recommended Array | Wiring & Vmp | Sun Hrs to Recover | 0–100% Full Pack |
|---|---|---|---|---|---|
| 10 km/day | 464 Wh | 150 W (1 panel) | 1S · 18 V Vmp | 4.9 hrs | 11.7 sunny days |
| 20 km/day | 928 Wh | 300 W (3 panels) | 3S · 54 V Vmp | 4.6 hrs | 5.9 sunny days |
| 30 km/day | 1392 Wh | 450 W (3 panels) | 3S · 54 V Vmp | 4.6 hrs | 3.9 sunny days |
| 35 km/day | 1624 Wh | 480 W (4 panels) | 2S2P · 36 V Vmp | 5.2 hrs | 3.4 sunny days |
| 40 km/day | 1856 Wh | 600 W (3 panels) | 3S · 54 V Vmp | 4.7 hrs | 3 sunny days |

