Hardware

Read the OUTPUT Line — What Your Charger's Label Is Actually Telling You

Summary

The four numbers on the brick, and which two matter. OUTPUT volts is the constant-voltage target — 54.6 V on a 48 V pack — OUTPUT amps sets the wattage a solar kit has to beat, and the plug is measured with calipers rather than read off the label.

1 · Direct answer

The Line You Want, and the Two Above It

Read the OUTPUT line, not the INPUT line. A 48 V pack charges at 54.6 V — 13 cells at 4.2 V each — so the 54.6 V and 2 A beside OUTPUT are the constant-voltage target and the charge current, and 54.6 × 2 = 109 W is what a solar kit has to beat per hour.

Every US e-bike we record charges above its own battery badge. A RadRunner 2 is 48 V, 672 Wh with a 54.6 V, 110 W charger; a Lectric XP 3.0 is 48 V, 499 Wh, 54.6 V, 110 W; an Aventon Aventure 2 is 48 V, 720 Wh, 54.6 V, 160 W. Read INPUT and you hunt for a 240 V part for a 54.6 V port; read only the volts and you cannot tell the RadRunner's 7-hour charge from the Light Bee X's 4-hour one.

2 · INPUT vs OUTPUT

The Line You Actually Want

INPUT describes the wall and OUTPUT describes the bike. Only the OUTPUT line tells you what voltage your pack has to see, and it is the line most people read second because it sits under the AC figures.

Heybike prints both on one line for the Mars 3.0 — "Charger 2A, 54.6V output, 100V-220V AC input" — and the eye lands on the 100–220 first. A charger that accepts 100–240 V AC is not a 240 V charger; it is one you can plug into any US outlet. The INPUT current is a worst-case AC draw at the bottom of that range, and it never reaches the pack.

Aim a converter at the nominal badge instead of the OUTPUT figure and you charge a 13S pack to 3.69 V per cell — part-charged, not full. Aim above the OUTPUT figure to "make sure" and you are in the direction that damages cells.

3 · The cell arithmetic

Why 54.6 V for a 48 V Pack

A "48 V" pack is 13 cells in series; 54.6 V is those same 13 cells at 4.2 V each. The nominal badge is the middle of the discharge curve, the constant-voltage figure the top of it.

Lithium cells are counted in series, and each NMC group tops out at 4.2 V: 13 × 4.2 = 54.6. The 48 V badge is the same thirteen groups at about 3.7 V, roughly where the pack sits for most of a ride. The one pack in our data that states its own configuration proves it: the Light Bee X is 16S8P at 67.2 V.

It is a ceiling, not a law. Our NIU XQi3 record — 72 V, 2304 Wh — carries 82.5 V, below the 84.0 V twenty cells at 4.2 V would give: the series count is fixed by the pack, the top-of-charge is the maker's choice. Read 54.6 V as "a 54.6 V bike" and you will go looking for a 54.6 V panel.

Badge on the bikeSeriesCV targetRecorded on
36 V10S42.0 VTrek Allant+ 8, both Bosch PowerTubes, Aventon Aventure 3, Aventon Pace 4
48 V13S54.6 VRadRunner 2, Lectric XP 3.0 / XP4, Aventon Aventure 2, Heybike Mars 3, NIU KQi 300X
52 V14S58.8 Varithmetic only — our 52 V records are low confidence, so we name no model
60 V16S67.2 VSur-Ron Light Bee X (16S8P), Talaria Sting MX4
72 V lithium20S84.0 Varithmetic only — the one 72 V record we hold charges lower (below)
96 V26S109.2 VNIU XQi 500 — charger wattage and current both null, so we quote neither

CV targets from `vehicles.json`; the 52 V and 72 V lithium rows are arithmetic only (14 × 4.2 V and 20 × 4.2 V), and the 52 V vehicle records are `low` confidence so no model is named. The 96 V row's charger wattage and current are both `null` in the record.

4 · Current and watts

What Your Solar Kit Has to Beat

Multiply the OUTPUT volts by the OUTPUT amps and you have the charger's wattage — 54.6 × 2 = 109 W — and that, not the pack's watt-hours, is the rate a solar kit has to match.

A 54.6 V, 2 A charger is 109.2 W, recorded as 109 W on the Lectric XP4, Heybike Mars 3 and NIU KQi 300X and as 110 W on the RadRunner 2, so identical bricks wear two badges. Keep the charger's current separate from the pack's: the Light Bee X's 672 W brick at 67.2 V is 10 A against a 12 A pack limit.

Watt-hours say how much a full charge is; watts say how fast it arrives. The RadRunner 2's 672 Wh pack and 110 W charger are recorded as a 7-hour charge, and 672 ÷ 110 = 6.1 h of ideal transfer — the rest is the taper at the end. A kit charges slower than the wall on purpose: the array gives what the hour gives. How many watts of panel that takes is guide #1's question.

5 · Lead-acid

The 72 V Label That Reads 88.2 V

A 72 V lead-acid or "graphene" pack is six 12 V blocks in series, and its absorption voltage is 86.4–88.2 V. An 88.2 V label on a "72 V" scooter is not a misprint.

Six blocks of six lead-acid cells makes 36 cells, and the pack wears four different voltages depending on what it is doing:

86.4–87.0 V is the standard VRLA/AGM cyclic target; 88.2 V is the fast-cyclic ceiling used on graphene-doped plates, and OEM "72 V" chargers are sold at exactly 88.2 V ± 0.5 V. The figure is also a 25 °C figure: absorption is temperature-compensated at about −30 mV per °C per block, so the same pack at 35 °C wants 84.6–86.4 V. Those are chemistry landmarks from our boost-controller research, not settings we are telling you to enter. No US e-bike in our data is lead-acid, so this is about a 72 V scooter's brick.

State of the packPer cellPer 12 V block72 V pack (6 blocks)
Resting, full and idle2.13–2.17 V12.80–13.00 V76.8 V – 78.0 V
Float2.25–2.30 V13.50–13.80 V81.0 V – 82.8 V
Standard cyclic absorption2.40–2.42 V14.40–14.50 V86.4 V – 87.0 V
Graphene fast-cyclic ceiling2.45 V14.70 V88.2 V

Per-cell, per-block and pack figures from `BOOST_CONTROLLER_RND_REPORT.md` §1.1; the pack column is six 12 V blocks in series (6 × 14.4 = 86.4 V, 6 × 14.7 = 88.2 V, 6 × 12.8 = 76.8 V).

6 · The plug

Identifying It Without Guessing

The label almost never names the plug. Count the contacts, measure the barrel with calipers, photograph the socket on the bike, and look for a moulded part number on the plug body.

Two contacts is a barrel or a plain 2-pin plug; three is a circular shell that may still be two-wire; four or more with a data group is a handshake a passive DC source cannot drive.

A "2-wire DC" port carries current and nothing else: no sense line, no detect contact, no conversation. The LP-20's unwired third pin does not stop it being two-wire. What stops it is a system bike — the Trek Allant+ 8 and both Bosch PowerTubes are marked not kit-eligible because the 4-pin BES2/BES3 socket is keyed and the pack runs a CAN challenge-response only a Bosch charger can answer.

Fit a DC5521 pigtail to a DC5525 socket and there is no centre contact — the pack does not charge and the plug still feels fine. Fit a 24–30 V CCTV pigtail into a 54.6 V port and the barrel jack is what melts.

FamilyContacts and sizeWhere we have recorded it
DC55212 contacts, 5.5 × 2.1 mm barrel, centre positiveLectric ≤2024 (XP 1.0–3.0), Ride1Up Portola, RadRunner family from 2022
DC55252 contacts, 5.5 × 2.5 mm barrelHeybike Mars 3.0
Junlei 30153-pin keyed circularLectric 2025+ — its own charger page says "Connector: JUNLEI 3015"
Higo / Julet Z3113-pin waterproof circularAventon Aventure — charger male Z311AG-P into battery female Z311AM-C
XLR 3-pin3-pin circularolder Rad generation; charger part PCL4803001 is "48V (XLR 3-pin)"
CNLinko LP-203-pin, 20 mm bayonetSur-Ron Light Bee X — pin 1 +, pin 2 −, pin 3 not connected
Chogori M238 contacts (2+1+5), push-locking, ~26 mme-motorcycle charge ports generally
Higo S828B8 contacts (2+1+5), rotating self-locking, 28–29 mmnot an M23 — same count, different face, no rotation maps one onto the other

Contact counts and shell sizes from `chargePorts.json`, except Higo / Julet Z311, which is a research-table attribution from `US_LAUNCH_PLAN.md` §4 (a 1st-gen 48 V Aventon Aventure teardown) and not a `chargePorts.json` field — the `aventon-charge` record is still `unknown`. DC5521 and DC5525 come from the `dc5521-charge` and `dc5525-charge` records.

7 · No label

When the Brick Tells You Nothing

If the OUTPUT line is worn off, do not guess the charge voltage from the battery's nominal figure. Use the cell count to know what you are looking for, then get the number from the maker.

Three places carry it: the OEM charger's nameplate, the pack's label, and the vehicle or battery manufacturer, in that order. The arithmetic tells you the family — a 48 V pack is 13S, so its charger is a 54.6 V unit — but not the top-of-charge that maker chose, and the XQi3's 82.5 V is the proof.

Replacement listings are a fourth source and frequently wrong: our KQi 300X record carries NIU's own 54.6 V, 2.0 A beside a third-party replacement at 53.5 V for the same family. Nor read the badge — 48 V is 3.69 V per cell on a 13S pack. When the only number you can find is a nominal voltage, you have not found the number.

8 · Before you connect

The Three Checks

Three checks before anything is connected: the OEM charger's DC output figure off its nameplate, the port's polarity on an isolated plug with a multimeter, and a fuse in the vehicle-side lead you add.

The nameplate check is this guide — OUTPUT volts and amps off the brick, not off the box or the listing. The polarity check belongs to the next guide, how to read and meter an e-bike charge port — /guides/how-to-read-and-meter-an-ebike-charge-port — because polarity is measured, never read, and red and black are a convention rather than a standard.

The fuse goes in the lead you add, rated for the cable, close to the vehicle end — defence in depth rather than a requirement, since the vehicle has its own main fuse, but the vehicle-side run is where it belongs: the pack sits behind it. And the thing this guide cannot give you is a number to enter anywhere — your controller's output is set to your own pack's constant-voltage figure, from your own charger's label, confirmed with a meter.

FAQ

Common Questions

Why does my 48 V e-bike charger say 54.6 V instead of 48 V?

Because 48 V is the nominal figure and 54.6 V is the top of the charge. A 48 V lithium pack is thirteen NMC cells in series, and each cell tops out at 4.2 V: 13 × 4.2 = 54.6. The 48 V badge is those same cells at about 3.7 V each, which is where the pack sits for most of a ride. Both numbers describe one battery at different points on its discharge curve, and the charger's OUTPUT line always states the higher one.

Does the INPUT or the OUTPUT number matter on a charger?

OUTPUT, every time. INPUT is 100–240 V AC and the current the brick draws from the wall — it describes the outlet, not the bike, and it is the number most people read first because it comes first on the label. OUTPUT is the DC voltage and current the pack actually receives. A charger with a 100–240 V input is not a 240 V charger; it is one that works on any US outlet and most others.

My scooter is 72 V but the charger says 88.2 V. Is the charger wrong?

No. A 72 V lead-acid or graphene pack is six 12 V blocks — 36 cells — and its absorption phase runs at 14.4–14.7 V per block, which is 86.4–88.2 V for the pack. The same pack rests at 76.8–78.0 V when full and floats at 81.0–82.8 V. A 72 V lithium pack is a different animal and charges at 84.0 V. The label is telling you the chemistry as well as the voltage.

How do I tell a DC5521 from a DC5525 without the label?

Measure the centre pin with calipers. Both families have a 5.5 mm outside diameter shell, so the outside tells you nothing useful; the centre pin is 2.1 mm on a DC5521 and 2.5 mm on a DC5525. They do not interchange in either direction — a 2.1 mm plug in a 2.5 mm socket makes no centre contact and the pack simply does not charge, while a 2.5 mm plug will not enter a 2.1 mm socket at all.

Can I use a charger with a higher current rating than the one that came with the bike?

Only up to the pack's own limit, which is a separate figure from the charger's. The Sur-Ron Light Bee X records a 672 W charger at 67.2 V — 10 A — while the pack's recorded maximum charge current is 12 A, so the brick sits deliberately below what the cells accept. The Aventon Aventure 2 ships a 3 A unit at 54.6 V. A charger's current is what its maker chose to give; the pack's current is what it will take.

What if the label on my charger is worn off completely?

Work down three sources in order: the OEM charger's nameplate, the pack's label, and the vehicle or battery manufacturer. Do not invent the figure from the nominal voltage — a 48 V pack's charger is a 54.6 V unit, but the maker's actual top-of-charge can sit below the textbook 4.2 V per cell, and our NIU XQi3 record is exactly that at 82.5 V on a 72 V pack. If you cannot find the number, ask the manufacturer rather than guessing.

Ready to Price Your Solar Kit and Payoff Period?

Pick your e-bike or scooter, choose foldable or rigid panels, and get your complete parts list in seconds.

Price My Solar Kit (Free) →